Hi Morota-sanSorry for Japanese銀ぺのは

Hi Morota-san

Sorry for Japanese
銀ぺのはみだしとPZTズレの（1）の回答は賛成です。
ただ、2）Reject if gap between PZT encapsulate and support-bridge larger than support-bridge width
この規格は教えた記憶がありません。

添付PDFを渡しズレたものは迷うものは工具顕微鏡にて測定としてあります。

GRRの資料ですが、16番（NCA spatter）と18番（Excess ECA）は写真を見る限りOKで良いと思います。
絶縁の飛びちりは大きさ400μ以下が3個以下の事。ボス穴上の0.8穴の半分より小さいかと。。。。

銀ぺはみだし、規格添付しておHi Morota-san

Sorry for Japanese
銀ぺのはみだしとPZTズレの（1）の回答は賛成です。
ただ、2）Reject if gap between PZT encapsulate and support-bridge larger than support-bridge width
この規格は教えた記憶がありません。

添付PDFを渡しズレたものは迷うものは工具顕微鏡にて測定としてあります。

GRRの資料ですが、16番（NCA spatter）と18番（Excess ECA）は写真を見る限りOKで良いと思います。
絶縁の飛びちりは大きさ400μ以下が3個以下の事。ボス穴上の0.8穴の半分より小さいかと。。。。

銀ぺはみだし、規格添付しておきましたがﾌﾚｷｱｰﾑの頂点まで行かなければOKなのでMarginal OKで良いかと思います。

以上、宜しくお願い致します。

千賀
きましたがﾌﾚｷｱｰﾑの頂点まで行かなければOKなのでMarginal OKで良いかと思います。

以上、宜しくお願い致します。

千賀

ผลลัพธ์ (อังกฤษ) 1:

Hi Morota-sanSorry for JapaneseLeaking of silver and PZT misalignment (1) of the answers are in favor.However, 2 ） Reject if the gap between PZT encapsulate and support-bridge larger than support-bridge width This standard is not taught memory.Is adopted, pass the attached PDF is lost have measurements at tool maker's microscope.As far as GRR article, but see photo （ NCA spatter ） No. 16 and no. 18 (Excess ECA) OK good I think.Insulation scatter on the 400 μm below the size of 3 or less thing. And less than half of the 0.8 hole boss holes on small.Silver is concerned the standards attached to your Hi Morota-sanSorry for JapaneseLeaking of silver and PZT misalignment (1) of the answers are in favor.However, 2 ） Reject if the gap between PZT encapsulate and support-bridge larger than support-bridge width This standard is not taught memory.Is adopted, pass the attached PDF is lost have measurements at tool maker's microscope.As far as GRR article, but see photo （ NCA spatter ） No. 16 and no. 18 (Excess ECA) OK good I think.Insulation scatter on the 400 μm below the size of 3 or less thing. And less than half of the 0.8 hole boss holes on small.Silver is concerned, I've attached standard is to go up to the top of the ﾌﾚｷｱｰﾑ OK so Marginal OK good I think.More than a thank you.SengaOK to go up to the top of the ﾌﾚｷｱｰﾑ has been so Marginal OK good I think.More than a thank you.Senga

ผลลัพธ์ (อังกฤษ) 2:

Hi Morota-san Sorry for Japanese answers of silver pair protrusion and PZT displacement (1) I agree. However, 2) Reject if gap between PZT encapsulate and support-bridge larger than support-bridge width does not have this standard memory you have taught. Attached PDF me what was shifted those that get lost you there as measured by the tool microscope. Although it is material of GRR, 16 th (NCA spatter) and 18th (Excess ECA) I think that may be a OK as long as you look at the photos. Flying dust of insulation size 400μ following three following things. As or smaller than half of the 0.8 hole on the boss hole. . . . Silver pair protrusion, your Hi Morota-san with standard attachments Sorry for Japanese silver pair protrusion and PZT displacement of (1) answer is favor. However, 2) Reject if gap between PZT encapsulate and support-bridge larger than support-bridge width does not have this standard memory you have taught. Attached PDF me what was shifted those that get lost you there as measured by the tool microscope. Although it is material of GRR, 16 th (NCA spatter) and 18th (Excess ECA) I think that may be a OK as long as you look at the photos. Flying dust of insulation size 400μ following three following things. As or smaller than half of the 0.8 hole on the boss hole. . . . The silver pair protruded, I've leave standard attachments and I think whether may be a OK so Marginal OK to have to go to the top of the Furekiamu. More, thank you. The Chika but came to think whether may be a OK so Marginal OK to have to go to the top of the Furekiamu. More, thank you. Chika

ผลลัพธ์ (อังกฤษ) 3:

Sorry Hi Morota too for Japanese silver at the San ぺのはみだしと PZT deviation of (1) the answer is yes. However, if Reject) at the gap between PZT formatused bridge support and larger than the width of the bridge support this standard is not teaching. PDF attached to give things lost are shifted as a tool in microscopy. The material of GRR 16 (NCA spatter) and 18 (Excess ECA) photos and good OK. At400. Mu. The following three or less that the size of the dust flying. And on a boss hole is smaller than a half of the 0.8.). Silver ぺはみだし too attached, you Hi Sorry standards for Morota too at the San Japanese silver ぺのはみだしと PZT deviation of (1) the answer is yes. However, if Reject) at the gap between PZT formatused bridge support and larger than the width of the bridge support this standard is not teaching. TooI have attached PDF things lost are shifted as a tool in microscopy. The material of GRR 16 (NCA spatter) and 18 (Excess ECA) photos and good OK. At 400. Mu. The following three or less that the size of the dust flying. And on a boss hole is smaller than a half of the 0.8.). I think so, too ぺはみだし silver OK must go to the top was attached to the standard of ﾌﾚｷｱｰﾑ Marginal OK is good. More, please help me. TooSo I have to go to the OK Chika was at the top of ﾌﾚｷｱｰﾑ Marginal OK is good. More, please help me. Chika, too.