①ボンベ交換の教育があったようですが ボンベの交換（バルブの開閉、チ

①ボンベ交換の教育があったようですが
ボンベの交換（バルブの開閉、チューブ取り外し取り付け）
は納入業者で行って頂けると聞いていましたが
それで間違いないでしょうか？
②吹き込みテストを行いましたが
単体でN2はmax6.9 cl2はmax37.7を表示します。
単位をたずねたところL/minとのことでした。
L/minですと圧力計が無いのでKg/Hrに換算できません。
NL/minでは到底両方とも必要量に足りません。
我々の必要量はN2：40Kg/Hr CL2：35Kg/Hrです。
N2流量計の承認資料を見ると単位はNL/minのようです。
自分で圧力を検知しNL/minに換算する流量計なのでしょうか？
CL2のほうも同じでしょうか？
・単位は何なのか？
・いずれにしても（NL/min、l/min）流量不足です。
ボンベ側、塩素室側の圧力を上げればいけるのでしょうか？

ผลลัพธ์ (อังกฤษ) 1:

(1) cylinder Exchange education was Replacement of the cylinder (replacing the valve opening and closing and removing the tube) Is heard can be done at the supplier So no doubt?(2) did the injection test In N2 shows max37.7 is max6.9 cl2. Asked the unit was and l/min. Because there is a l/min and pressure gauge cannot be converted to kg/HR. NL/min is possibly both should amount to enough. Our requirement: N2: 40 kg/HR CL 2 is 35 kg/HR. View N2 flow meter approved material and unit seems to be NL/min. A flowmeter detects the pressure yourself, equivalent to NL/min? Cl2 is the same? What is the unit? And either way (NL/min, l/min) flow rate is insufficient. Can you raise the pressure of the tanks and chlorine room side?

ผลลัพธ์ (อังกฤษ) 2:

① education is had like but of cylinder exchange
exchange of cylinders (the opening and closing of the valve, remove the mounting tube)
was, I have heard and who can be performed in suppliers
or will no doubt so?
② I've tested blowing
N2 by itself max6.9 cl2 displays the max37.7.
Was that of the place L / min which asked the unit.
Since when is L / min there is no pressure gauge can not be converted to Kg / Hr.
Both hardly in NL / min not big enough to be required amount.
Our required amount of N2: 40Kg / Hr CL2: is 35Kg / Hr.
Units If you look at the approval document of N2 flow meter is like a NL / min.
Will you flowmeter to be converted into detects the pressure NL / min by yourself?
What same even more of CL2?
What is and unit?
- Either by (NL / min, l / min) is a flow shortage.
Cylinder side, Will you go To take the pressure of the chlorine chamber side?

ผลลัพธ์ (อังกฤษ) 3:

Replacement of the cylinder that is the replacement of Education (will no doubt heard by the supplier, and has been removed from the tube, including installation. So, the valve is opened. Test
② was blowing in the N unit 2 max Max 37.7 6.9 Cl2. When asked at the unit of L / min. At the L / min, and because there is no pressure gauge in Kg Hr and cannot be converted. In NL min would need to be both. AtRequirement of our N 2: 2: Kg 40 and Hr CL Kg and Hr 35. To see the documents of approval N 2 meter unit is NL / min. Flow meter at yourself by detecting the pressure to convert NL min? But at the same CL 2? What is at the unit? If at any (NL min, L / min) is lack of flow rate. At the side of the chlorine cylinder chamber will raise pressure on?