加硫工程での条件管理実施検査基準書に基づき、重要管理寸法測定机上検討に

加硫工程での条件管理実施

検査基準書に基づき、重要管理寸法測定

机上検討による寸法設定
新機種設定時のﾄﾗｲ実施
新機種設定時のﾄﾗｲ実施
新機種設定時のﾄﾗｲ実施
新機種設定時のﾄﾗｲ実施
治具へｾｯﾄ前に目視確認を作業標準化
治具へｾｯﾄ前に目視確認を作業標準化
治具は部品別に準備しﾄﾞｸﾞにより，治具No.識別する

"NG発生時ﾍﾟｲﾝﾄﾏｰｶｰにてﾜｰｸに
ﾏｰｷﾝｸﾞしないとNGﾘｾｯﾄができない
機構及び標準作業を実施"

ASSY時の寸法測定による、ｽﾌﾟﾘﾝｸﾞﾊﾞｯｸ量修正機能設定実施

ผลลัพธ์ (อังกฤษ) 1:

Under the terms management practices

inspection standard in the vulcanization process, implementation of the tri-tri
new models setting up a tri implementation
new models when configuring sized
new models by setting up important management dimensional measurement

desk study The dog, work standardization
jig to jig no. identified prepared parts another visual confirmation to set before to work standardization
jig visual confirmation to set before to try implementation
jig of implementation
new models when setting

can not be reset ng "ng occurs in paint marker to work if you do not

markingConducted standard work and mechanism "

by dimensional measurement of assy time, the amount of springback correction setting implementation

ผลลัพธ์ (อังกฤษ) 2:

Condition management conducted in the vulcanization process

important management measure, based on inspection standards

dimensions set by the preliminary investigation
ﾄﾗｲ implementation of new models set
ﾄﾗｲ implementation of new models when
ﾄﾗｲ implementation of new models set at
ﾄﾗｲ implementation of new models set
set prior to examine work standards to Jig
set prior to examine work standards to Jig
and prepare the fixture parts, Jig fixture No by ﾄﾞｸﾞ,... to identify

"at NG occurs when ﾍﾟｲﾝﾄﾏｰｶｰ to work
cannot and do not ﾏｰｷﾝｸﾞ NG reset
Conducting mechanism and standard work "

ASSY: dimensional measurement using ｽﾌﾟﾘﾝｸﾞﾊﾞｯｸ amount fixed feature set implementation

ผลลัพธ์ (อังกฤษ) 3:

Based on an examination for condition management enforcement

workbook by the vulcanization process, the work standardization
jig prepares for viewing confirmation according to a part before a set to a work standardization
jig by viewing confirmation before a set to a try enforcement
jig at the time of the try enforcement
new model setting at the time of the try enforcement
new model setting at the time of the try enforcement
new model setting at the time of the dimensions setting
new model setting by examining important management dimensional measurement

on desk;, by ドグ, is jig No.When
doesn't mark a work in a

"NG outbreak time paint marker to distinguish, NG reset isn't possible
Quantity of spring background correction mechanism setting by the dimensional measurement in enforcement "

ASSY carries out mechanism and standard work